Behringer xenyx 1222fx
repair/popravilo
Xenyx 1222fx
Repairing the
jack socket/popravilo jack vtičnice
Zaradi
dotrajanosti ali slabega vzdrževanja,izpostavljanja tekočinam,transporta itd..se
nam lahko večkrat zgodi da poškodujemo elektronski element. Naprave ne moremo
uporabljati pravilno.
Due to expire
or poor maintenance, exposure to liquids, transport, etc. .. we may
happen several times to faul the
electronic element. The
device can not be used properly.
Previdno
odvijemo zgornji del z vijaki na straneh. Odvijemo tudi vijake na zadnji strani
ohišja.
Carefully unscrew the top of the screws on the sides. Unscrew the screws on the rear of the chassis.
Odstranimo vijake pri napajalniku uporabimo manjši
izvijač,da jih ne poškodujemo. Previdno dvignemo pokrov naprave.
Remove the
screws from the power supply
using a small screwdriver that we can not damage
it. Carefully lift the cover off
the device.
Na ploščici tiskanega vezja odstranimo ostanke lepila pri konektorjih za napajanje in za signale.
We hate
to remove the remains of hot
glue from power connector and signals connectors
on the pcb.
Ker bomo
morali odstraniti tudi vezje z vtičnicami moramo odviti vse matice in vijake na
vtičnicah. Pazimo da ne poškodujemo zgornje strani ohišja.
Because we
have to remove the circuit board
with sockets we need to unscrew
all the nuts
and bolts on the socket. Take care not to damage the upper side
of the housing.
Šele
sedaj lahko začnemo z popravilom jack vtičnice.
Morali jo bomo odspajkati, da lahko odstranimo
zlomljen del jack vtikača. Odspajkamo
priključne pine konektorja
na spodnji strani vezja.
Only now
can we begin to repair the jack
socket. We'll have to unsolder
it, that we can remove a broken
part of the jack plug. Unsolder terminal pins of the
connector on the underside of the
circuit board.
Previdno
izvlečemo jack vtičnico. Sedaj lahko odstranimo del
zlomljenega jack vtikača,to je tulec,ki smo ga izvlekli
iz vtičnice.
Carefully pull
out the jack
socket. Now you can remove
the broken part of the jack
plug, this is a sleeve that we pulled
out of the
socket..
Izvlečemo
tudi ostanke zlomljenega jack vtikača,njegovo konico.
Pregledamo vtičnico,če je vse vredu, jo lahko ponovno
prispajkamo. Napravo sestavimo v nasprotnem vrstnem
redu,kot smo jo razstavili.
Pull out
the remains of the broken
jack plug, the tip. Examine the socket
if it is all right, it can be
resoldered. Assembly the device in reverse order, as we disassembled
it.
Opozorilo:AudioLogs ne odgovarja,za morebitne
napake med postopkom ali za škodo ki se lahko zgodi. Preden se lotite popravila
izključite aparat iz omrežja. S posegom v aparat lahko poškodujete vezje. Bodite
previdni pri popravilu vezja ,ker lahko poškodujete ploščo tiskanega vezja in
povezave. Če tega posega niste vešči naj za vas to opravi strokovnjak.
Warning: AudioLogs is not responsible, for the errors during the procedure or damage that may occur. Before you start to repair,plug
out unit from the network. By intervening in unit could damage the circuit. Be careful when you repairing
the pcb, you
can damage the pcb. If you are not skilled in this practice
should be done for you an expert.
AudioLogs,March2014,info@audiologs.com
If the information was useful for you, you can